Rokinon Teleconverter Stuck? Try This Step-by-Step Fix

Rokinon teleconverter stuck!  You are not alone if a Rokinon teleconverter gets stuck on your lens, as there are many other users looking for a solution. It is indeed an annoying issue that makes you have to come up with alternative means

Whenever you are out to take the ideal shots, however, we explore some helpful means you can adopt that are cheaper more than the actual aesthetic fixations, especially considering

The fact that fixing these parts can get extremely expensive. This paper will provide you with some non-invasive practices that will help you solve Rokinon teleconverter problems if you follow them carefully, in a methodical manner.

Why is Rokinon Teleconverter Jammed

A Rokinon teleconverter can be jammed due to many reasons so anytime your Rokinon teleconverter is jammed it could be that there is some dust, grit, or debris caught in the lens mount, the teleconverter has minor misalignment, or the threads on the teleconverter are almost worn out.

Knowing the point of failure will ideally assist you in determining what means you should aim at in order the fix it reverting it back to its unchanged state therefore reducing chances of damaging any reels. We can examine different methods that can work for each of the reasons mentioned.

Step 1: Set Up a Work Bench

Set up a workbench that is immaculate and out of debris before you proceed with fixing the issue of your Rokinon teleconverter’s jammed state. Make sure to that your camera and teleconverter sit in the soft pieces of cloth as it will not only help in avoiding dust formation around the camera lens but would also protect it from scratches.

1. Also make sure that you hand are completely clean and dried.
2. Your work area can be covered with a lint free cloth or a micro fiber piece of cloth.
3. Before beginning the steps, make sure you have a few basic cleaning tools such as, small brush, a can of compressed air, and, preferably, a dusting brush special for lens.

Step 2: Loosening the Teleconverter Gently

A bit of twist sometimes when Rokinon teleconverter stuck should be able to loosen it. Pick the teleconverter and give it a slight counterclockwise turn as though you are taking it off and do it lightly and gradually.

• Do not use too great force as this may damage the teleconverter or the attachment.
• Do not be too rapid in twisting as it may lead to friction which may twist the threads.

If there is no motion, inhaling and exhaling deeply is recommended to help to eliminate the impulse of going for a violent action. Other steps shown below have more ways to try.

Step 3: Using Compressed Air Approach to Remove Dust

More often the cause of the attachment in between the camera and the teleconverter is the dust or dirt. Around the mount area, where the two seem to join, take a few short sprays from a can of compressed air.

• Hold the can in a horizontal manner as much as possible so equipment can dry without moisture spraying from it.
• Make sure spraying occurs around the edges since that is where the teleconverter meets the body of the camera.

This method should assist in removing small particles or anything similar which might be causing blockage. However, if the teleconverter is still stuck, go on to the subsequent step.

Step 4: Brush The Collar Gently

With a small soft brush e.g. a lens brush, remove the materials along the edges of the Lens. Particles such as dust and sand could have been trapped in the elements when mounting the teleconverter to the lens and therefore need to be removed

• Start brushing in a circular motion, around the site of the joint.
• Pay particular attention to pieces of dirt and debris that are adjacent to the lock.

When the cleaning has been done, make an attempt to turn the teleconverter in a gentle manner, twisting it.

Step 5: Get an Alignment Check

The amount of shift that occurs within a teleconverter Rokinon visually may seem small but if it is out of place, it may cause a Rokinon teleconverter stuck situation. Check the collar ring section to confirm that the teleconverter is in the right position. If the teleconverter seems to be out of center, check the following:

1. Grasp the body of the camera as well as the teleconverter.
2. Slightly touch the camera body and the teleconverter in order to adjust the teleconverter, try to be careful of not doing so much that the teleconverter is forced.

Often being in a stuck position is sufficient to allow a teleconverter to be taken out by remaining in a stuck position.

Step 6: Use a Camera Lens Wrench for Stubborn Cases

If the teleconverter is still reluctant to budge, you could try employing a camera lens wrench which is made for this purpose tool. This is a useful tool for applying controlled, uniform force and an equal amount of grip without being too forceful.

1. With the teleconverter in one hand, gently place the wrench around the teleconverter ensuring a snug fit.
2. Wielding the wrench, apply even pressure while twisting it in the opposite direction.

This method normally works well in stubborn case where other attempts have failed or less likely to succeed.

Step 7: Contact a Professional if Needed

You can risk the last option of getting expert advice in case these steps do not help your Rokinon teleconverter stuck problem. Lens and camera repair experts have special tools and expertise in how to unscrew parts without causing any damage to the components in the process.

1. Carry your camera and teleconverter to the nearest repair shop that has been certified to provide such repairs.
2. Stay away from any kind of dealing along with the use of chemicals and lubricants as this may in an adverse way affect the teleconverter or camera body.
3. If the problem persists, avoid struggling by using home-based remedies if you have the option to seek the help of experts.

Avoiding A Future Stuck Rokinon Teleconverter

One could prevent their Rokinon Teleconverter from becoming stuck by adhering to the following and proper substitute measures:

1. Use your teleconverter with caution: When attaching teleconverters, make sure to properly align them to avoid twisting them unnecessarily.
2. Remove sand and dust: Make sure to clean both the Rokinon teleconverter and the camera lens mounts in order to prevent the possibility of dust from accumulating.
3. Work in a clean environment whilst storing: To avoid contact with dust or sand whilst not in use, store your Rokinon teleconverter in a case or bag that protects it.

Conclusion on Unjamming A Stuck Rokinon Teleconverter

rokinon teleconverter stuck there is a high probability of resolving your issue yourself due to a proper and gentle technique, making your approach systematic. Simple projects such as basic cleaning or implementing alignment checks will definitely work towards your success.

Should none of those suggested tips work, consulting a professional although slightly more expensive is preferable as it helps one to be careful and avoids incurring any unnecessary expenses.

Taking due care and being extra cautious are the right ways to ensure you are using your Rokinon teleconverter properly whilst working on photography without any issues.